A race night in RaceLyx always runs in the same order: Event Setup, entries and check-in, heats, Race Control, the next rounds, mains, bump-ups, results, then End Event. This page walks through the whole night once, so you know what comes next, and links each job to its own guide. The short video shows where each screen is; the written steps below are the checklist to keep open on the night.
Before you start
- The first-run setup done: your track and layout (Start here, First-run setup).
- A decoder connected on Timing Hardware, or the Simulator for a practice run at home.
- Your classes on Classes, and your regular drivers on Drivers with a car and transponder each. New drivers can be added at the desk.
- Home Track plan or above for circuit racing (the trial covers everything).
Step by step
- 1
1. Set up the event
Start in Event, Event Setup. Pick the classes racing, the qualifying rounds and heat size, and the mains, then Apply Setup.
Create an event walks through every step. The numbers that matter are on Qualifying (Rounds, Duration, Cars per Heat) and Mains (Cars per Race, length, bump-ups). Set it up days ahead with a future date (Schedule an event ahead), or save your usual night as a template (Event templates). With the event running, Event Setup becomes the event hub shown here, with Edit Event for changes.
- 2
2. Enter and check in drivers
As drivers arrive, open Race Control, Check-In. Find each driver, tick their classes and transponder, and click Enter and check in.
Only entered drivers are drawn into heats. Enter drivers in tonight's classes covers the driver card; A new driver at the desk covers first-timers; Check drivers in at the desk covers the regulars. Online sign-ups wait at the top under Waiting at the desk (Online pre-registration). Entry fees, waivers and pit spots are on the same card when your track uses them.
- 3
3. Draw and print the heats
When the door closes, open Heats & Program, Generate Heats, and untick anyone who has not turned up. Then Wall print the program for the pit wall.
Draw the qualifying heats covers the form: Type Qualifying, heat size and length from Event Setup, Random Shuffle, Separate heats per class. Move a driver with Edit Heats; deal with no-shows and late entries as in A no-show or late entry. Print the heat program covers Wall print and Quick print.
- 4
4. Run each heat
Run the heats from Race Control. Stage the heat, call the roll, start it, and at the flag click Save and Next Heat.
Stage a heat and run roll call, Start and run a heat, Caution, red flag and the clock, and Save the heat and go to the next cover each part. Penalties, lap corrections and stray transponders have their own guides in Race control. Save every heat before you stage the next one.
- 5
5. Next rounds, then the mains
After each round, Heats & Program asks how to set up the next. Pick Re-seed from Results. After the last round, click Build Mains.
Set up the next qualifying round explains the five choices. When qualifying is done, Build the mains seeds each class's mains from its qualifying, fastest in the A Main, lower mains first. With bump-ups on, RaceLyx asks who moves up after each lower main (Bump-ups between mains). Print the program again after each draw.
- 6
6. Results and End Event
Results fill in as you save. Print the event reports, then end the event from the event hub with End Event.
Final results for the event shows each class's finishing order; Print the event reports makes the sheets for the wall and the awards. Publish results online covers putting them on your public page when RaceLyx Cloud is on. End an event covers End Event: the summary goes to Past Events, and you can reopen it if you end it too soon.
Tips
- A week before: create the event with a future date (Schedule an event ahead), share your online sign-up link if you take entries online (Pro), and set up pit spaces if you use them (Club).
- An hour before: start the event, connect the decoder, open Check-In, and turn the Racer sign-in screen toward the door if you use it.
- Run a practice session while drivers arrive: it checks every transponder reads before the first heat.
- Draw the heats only when the door closes. Every entered driver is drawn, whether they checked in or not.
- Print the program after every draw: once for round 1, again after each re-seed, and again after Build Mains.
- Space bar starts the staged heat in Race Control. The ? key opens help on any screen.
- Save each heat with Save & Next Heat before you stage the next. Unsaved laps are what get lost.
- Print the event reports before you click End Event, while everything is in front of you.
- Do a dry run at home with the Simulator: set up a pretend event, draw heats and run one to the flag. It takes about fifteen minutes.
Troubleshooting
- "No drivers ready to draw" on Heats & Program.
- Nobody is entered in the event yet. Enter drivers on Check-In first; see Enter drivers in tonight's classes.
- A driver who went home is in a heat.
- Remove them from their heat on Heats & Program, and Withdraw them on Check-In. See A no-show or late entry.
- The next round did not draw itself.
- After the last heat of a round is saved, Heats & Program asks how to set up the next one. Pick Re-seed from Results. See Set up the next qualifying round.
- No laps are counting.
- Check Timing Hardware shows the decoder connected and passings arriving. See Decoder not seen.
Related guides
- Create an event about 2 min
- Enter drivers in tonight's classes about 1 min
- Check drivers in at the desk about 1 min
- Draw the qualifying heats about 1 min
- Print the heat program about 1 min
- Stage a heat and run roll call about 1 min
- Start and run a heat about 1 min
- Save the heat and go to the next about 1 min
- Set up the next qualifying round about 1 min
- Build the mains about 1 min
- Bump-ups between mains about 1 min
- Final results for the event about 1 min
- End an event about 1 min
Something here does not match what you see? Tell us and we will fix the guide.